E bike controllerÂ kit 250W 350wÂ 36V 48V DC Mode e scooter Brushless Motor Controller with electric bike LCD. LCD display has different colors, we randomly send. This controller can work in hall sensor and also work in hall sensorless. 36V 48V 250W controller & 36V 48V 350W controller function. Red: battery +, Â black: battery - ï¼?Red line: positive input of power supply. White line: controller electric door lock. Black line: negative power supply. Working voltage: DC 36V/48V compatible (buyers can set by themselves according to their needs).
Display function Speed display, battery indicator, fault prompt, total mileage, single mileage. Power switch control, wheel diameter setting, idle automatic sleep time setting, backlight brightness setting, start Mode setting, driving mode setting, voltage level setting, controller current limit setting, USB charging function. All contents of the display (full display within 1S after power on).
Total mileage ODO, single mileage TRIP, digital voltage display VOL, fault. 0-13 Represents the following questions. 3 Power-assisted sensor failure (cycling sign) not implemented here.
If not connect controller hall aslo will show this error07. P01: Backlight brightness, level 1 is the darkest, level 3 is the brightest. P02: Mileage unit, 0: KM; 1: MILE. P03: Voltage level: 24V, 36V, 48V, default 36V.
P04: Sleep time: 0, no sleep; other numbers are sleep time, range: 1-60; unit minute. P05: Power-assisted gear position: 0: 3 gear mode. P06: Wheel diameter: unit, inch; precision: 0.1.
P07: Number ofspeed magnets: range: 0-255. P08: Speed limit: range 0-100km/h, unopened.
P09: Zero start, non-zero start setting, 0: zero start; 1: non-zero start. P10: Â Drive mode setting. 0: Power-assisted drive how much power is output through the power-assisted gear, at this time. 1: Electric drive (drive through the handlebar, at this time the assist gear is invalid). 2: Power-assisted drive and electric drive coexist at the same time.
P11: Assist sensitivity setting is not enabled. P12: Power-assisted start intensity setting is not activated. P13: Type setting of power-assisted magnetic steel plate is not activated. P14: Controller current limit setting default 12A range: 1-20A.
P16: ODO reset setting Long press the plus key for 5 seconds ODO reset. P17: 0: disable cruise, 1: enable cruise; automatic cruise is optional only valid for No. P18: Display speed ratio adjustment range: 50%150%. P19: 0 gear enable bit, 0: including 0 gear, 1: not including 0 gear. 2 protocol 1: 5S protocol 2: Standby 3: Standby.
Introduction to buttons and interface. In the shutdown state, long press the power button to turn on; after booting, short the power button, the interface is in ODO, Switch between TRIP and VOL. In the power-on state, long press the power button to turn off, and short press the MODE button to switch gears in the GEAR area (there are 1, 2, 3 gears).Long press the power + MODE button to enter the power-on password and menu setting selection interface (S0 interface). In the S0 interface, short press the power button to switch the number of password digits, and short press the MODE button to change the current digit value. 3.1 After entering "1111", long press the power button to enter the S1 interface, short press the power button to switch the digits of the password, short press the MODE button to change the current digit value, after the password is modified, Â press and hold the power button at the same time to exit the S1 interface to the normal display interface, And save the password set last time Note: You need to enter this password next time you turn on the machine. 3.2 After entering "6666", long press the power button to enter the menu setting interface, in any parameter state, short press the power button to switch parameters, short press or long button MODE to increase or decrease the value long press the power button to change the direction of value addition and subtraction, â?? On the left means increasing the value, and â?? On the left means decreasing the value. After the modification is completed, short press the power button to switch to the next parameter and save the previous parameter value; after the parameter modification is completed, it will be long again Press the power + MODE button to exit the setting interface, or wait for 8 seconds to automatically exit and save the parameters.
Operation of the backup "3745" passwordï¼? If you forget the password when powering on, enter the â?? Backup password and press and hold the MODE button for 10 seconds to enter the normal interface.
This item is in the category "Sporting Goods\Cycling\Bicycle Components & Parts\Electric Bicycle Components". The seller is "pahar_7578" and is located in this country: CN.This item can be shipped to United States.